CHT-60 Series
Carbide Hand Taps for Hardened Steels
● Features
This tap is specially designed for tapping hardened steels with hardness from 50 to 60 HRC.
| Type of thread | Ic 3P | Ic 5P | Tap Limit | L | I | d | Kl | K | F |
|---|---|---|---|---|---|---|---|---|---|
| M2 × 0.4 | 14001 | 14101 | EL3 | 40 | 12 | 3 | 5 | 2.5 | 3 |
| M2.3 × 0.4 | 14002 | 14102 | EL3 | 42 | 13 | 3 | 5 | 2.5 | 4 |
| M2.5 × 0.45 | 14003 | 14103 | EL3 | 44 | 14 | 3 | 5 | 2.5 | 4 |
| M2.6 × 0.45 | 14004 | 14104 | EL3 | 44 | 14 | 3 | 5 | 2.5 | 4 |
| M3 × 0.5 | 14005 | 14105 | EL3 | 46 | 11 | 4 | 6 | 3.2 | 4 |
| M4 × 0.7 | 14006 | 14106 | EL3 | 52 | 13 | 5 | 7 | 4 | 4 |
| M5 × 0.8 | 14007 | 14107 | EL3 | 60 | 16 | 5.5 | 7 | 4.5 | 4 |
| M6 × 1.0 | 14008 | 14108 | EL3 | 62 | 19 | 6 | 7 | 4.5 | 5 |
| M8 × 1.25 | 14009 | 14109 | EL3 | 70 | 22 | 6.2 | 8 | 5 | 5 |
| M8 × 1.0 | 14010 | 14110 | EL3 | 70 | 22 | 6.2 | 8 | 5 | 5 |
| M10 × 1.5 | 14011 | 14111 | EL3 | 75 | 24 | 7 | 8 | 5.5 | 5 |
| M10 × 1.25 | 14012 | 14112 | EL3 | 75 | 24 | 7 | 8 | 5.5 | 5 |
| M10× 1.0 | 14013 | 14113 | EL3 | 75 | 24 | 7 | 8 | 5.5 | 5 |
| M12× 1.75 | 14014 | 14114 | EL3 | 82 | 29 | 8.5 | 9 | 6.5 | 5 |
| M12 × 1.5 | 14015 | 14115 | EL3 | 82 | 29 | 8.5 | 9 | 6.5 | 5 |
| M12 × 1.25 | 14016 | 14116 | EL4 | 82 | 29 | 8.5 | 9 | 6.5 | 5 |
| M12 × 1.0 | 14017 | 14117 | EL3 | 82 | 29 | 8.5 | 9 | 6.5 | 5 |
| M14 × 2.0 | 14018 | 14118 | EL4 | 88 | 29 | 10.5 | 11 | 8 | 6 |
| M14 × 1.5 | 14019 | 14119 | EL3 | 88 | 29 | 10.5 | 11 | 8 | 6 |
| M16 × 2.0 | 14020 | 14120 | EL4 | 95 | 29 | 12.5 | 13 | 10 | 6 |
| M16 × 1.5 | 14021 | 14121 | EL3 | 95 | 29 | 12.5 | 13 | 10 | 6 |
| M18 × 2.5 | 14022 | 14122 | EL4 | 100 | 35 | 14 | 14 | 11 | 6 |
| M18 × 1.5 | 14023 | 14123 | EL4 | 100 | 35 | 14 | 14 | 11 | 6 |
| M20 × 2.5 | 14024 | 14124 | EL4 | 105 | 35 | 15 | 15 | 12 | 6 |
| M20 × 1.5 | 14025 | 14125 | EL4 | 105 | 35 | 15 | 15 | 12 | 6 |
