SPS Series
Thread Position Alignment Gauge Pos-T
The thread section serves as the GO side thread plug gauge, allowing for very precise measurement of the hole position.
Features
- The thread section satisfies GO side thread plug gauge standards, so that can do GO check of a tapped hole at the same time.
- Checking the squareness is possible by checking the gap with the end face of pin gauge section.
- The gauge material is Gauge steel (SKS3, HRC58 or harder), and the gauge has exceptional wear resintance.
- This gause is equipped with a removable knurled handle, not to touch the pin gauge section directly (The handle can be removed if it interferes with the measurement).
- An inspection report for the thread gauge and pin gauge sections is included with to provide confidence and assurance for users!
Example
Go Metric Thread Plug Gauge
Type of thread | Pitch | L | D | a | b | Y | L1 | Type of Gauge | Class | ||
---|---|---|---|---|---|---|---|---|---|---|---|
M3 | 0.5 | coarse | 10 or 22 | 7 | ±0.001 | 5 | 2 | 6 | 10 | GP | Ⅱ(JIS Class) 6H (ISO Class) ※M1.4[5H] |
M4 | 0.7 | coarse | 6 | ||||||||
M5 | 0.8 | coarse | 8 | 7 | |||||||
M6 | 1.0 | coarse | 9 | 8 | 2.5 | ||||||
M7 | 1.0 | coarse | 10 | ||||||||
M8 | 1.25 | coarse | 11 | ±0.0015 | 10 | 3 | 10 | ||||
M8 | 1.0 | fine | |||||||||
M9 | 1.25 | coarse | 12 | ||||||||
M10 | 1.5 | coarse | 13 | 12 | |||||||
M10 | 1.25 | fine | |||||||||
M10 | 1.0 | fine | |||||||||
M12 | 1.75 | coarse | 15 | 14 | |||||||
M12 | 1.5 | fine | |||||||||
M12 | 1.25 | fine | |||||||||
M14 | 2.0 | coarse | 17 | 14 | 14 | ||||||
M14 | 1.5 | fine | |||||||||
M14 | 1.25 | fine | |||||||||
M16 | 2.0 | coarse | 19 | ||||||||
M16 | 1.5 | fine | |||||||||
M18 | 2.5 | coarse | 21 | ±0.002 | 16 | 4 | |||||
M18 | 2.0 | fine | |||||||||
M18 | 1.5 | fine | |||||||||
M20 | 2.5 | coarse | 23 | ||||||||
M20 | 2.0 | fine | |||||||||
M20 | 1.5 | fine |
- ※Other specifications are available (effective diameter can be changed for fine, extra-fine, and pre-plating sections).
Unified thread plug gauge
coarse | fine | L | D | a | b | Y | L1 | Type of gauge | Class |
---|---|---|---|---|---|---|---|---|---|
No.4-40UNC | No.4-48UNF | 10 or 22 | 7 | 5 | 2 | 6 | 10 | GP | 2B (JIS Class) |
No.5-40UNC | No.5-44UNF | 6 | |||||||
No.6-32UNC | No.6-40UNF | ||||||||
No.8-32UNC | No.8-36UNF | ||||||||
No.10-24UNC | No.10-32UNF | 8 | 7 | ||||||
No.12-24UNC | No.12-28UNF | ||||||||
1/4-20UNC | 1/4-28UNF | 9 | 8 | 2.5 | |||||
5/16-18UNC | 5/16-24UNF | 11 | 10 | 3 | 10 | ||||
3/8-16UNC | 3/8-24UNF | 13 | 12 | ||||||
7/16-14UNC | 7/16-20UNF | 14 | 14 | ||||||
1/2-13UNC | 1/2-20UNF | 16 | 14 | 14 | |||||
9/16-12UNC | 9/16-18UNF | 17 | |||||||
5/8-11UNC | 5/8-18UNF | 19 | |||||||
3/4-10UNC | 3/4-16UNF | 22 | 16 | 4 | |||||
7/8-9UNC | 7/8-14UNF | 25 | 20 | 5 | |||||
1-8UNC | 1-12UNF | 28 |
- ※Other specifications are available (effective diameter can be changed for fine, extra-fine, and pre-plating sections).